How To Repair Broken Glasses Bridge

Download Article

Download Article

Breaking your eyeglasses tin can be frustrating, and you might non e'er be able to supersede them correct abroad. Whether you scratched the lense, lost a screw, or bankrupt the bridge, y'all tin can repair your eyeglasses yourself to hold you over until you are able to get a new pair.

1. ane

   Get your materials in identify. You'll need a thread, needle, drill, sandpaper, superglue, painter'southward stir stick, condom bands, waxed newspaper, cotton fiber swabs, alcohol or nail polish remover and a hobby pocketknife.

2. 2

   Clean and sand the broken pieces. Apply sandpaper to clean and rough up the broken expanse to be glued. Swab the area with some rubbing alcohol or nail polish remover to prepare the surface.

3. iii

   Secure the two pieces together. Cut a slice of a painter's wooden stir stick to fit between the temples (aka, the side pieces) of your glasses. Cover your lenses with wax paper to prevent scratching and and then wrap a rubber band over ane end of the stick and secure information technology to your glasses. Do the same on the other stop.

   • Line the 2 halves up carefully and be sure the rubber bands are holding things firmly in identify. If information technology wasn't a clean intermission and in that location are some gaps, line the pieces up as best you can taking pains to ensure at that place are some definite points of contact.^[iii]

4. iv

   Glue. Fill the joint at the break with glue; employ enough to secure the bridge but not and so much that the glue runs out. Squeeze out the glue slowly and neatly to avoid bubbles. Every bit you fill in the joint, be certain that there are no gaps or voids. Apply the side of a cotton fiber swab to gently clean up any excess glue; swab information technology up before it has a chance to dry and get tacky. Set the glasses aside for at least an hour so the gum can dry completely.

5. 5

   Drill two holes. Cull a small drill bit appropriate for the thickness of your eyeglass frames. Have your hobby pocketknife and dig out pilot holes on either side of the newly repaired articulation. Identify your spectacles down on a soft cloth that'due south been laid on a table top and carefully drill a hole on each side of the suspension. The holes must be parallel so they can be used to wrap a band of thread around the core joint.^[4]

6. half dozen

   Run up a tension band in place. Utilize a fine needle and four to six feet of thread that matches the color of your eyeglass frames to "stitch" the two sides of the repair together for added strength. Laissez passer the needle and thread through the two holes every bit many times every bit you can taking care non to pull also difficult and put stress on the newly repaired articulation. Stop when in that location's no more room. Fill the drilled holes with glue, soaking the thread and blotting upward whatever excess with a cotton swab. Trim the edges of the thread and permit the glue to dry for at to the lowest degree an hr.

7. 7

   Add a wrap. If y'all want to requite extra strength to your repair, you can add this additional pace to your process. Practise not trim the edges of the thread as above. Instead, after your mucilage has dried, take the remaining thread from ane side and wrap it around the bridge of your glasses from front to back. Make your wrap every bit neat as possible; some criss-crossing may exist unavoidable, but practice your best to prevent the wrap from looking beefy. Leave a brusque terminate to be trimmed later. Soak the wrap with glue and let it dry out for 10-15 minutes. Have the thread from the other side of your glasses and wrap it around the bridge in the opposite management (back to front end). Soak the new wrap in glue and permit it cure for a couple of minutes earlier snipping off the two loose ends. Set your spectacles bated for 24 hours before wearing.

Advertising

1. 1

   Boil h2o. Fill a small pot with water and set the flame to "high." Because yous're going to employ rut for this repair, the frames of your glasses must be plastic for it to work.

2. 2

   Melt the plastic. Once the h2o is boiling, hold the broken edges of the glasses over the pot and shut enough for the oestrus to soften the edges.

3. iii

   Insert a pivot. Push a short pin into one border and then push the other edge onto the pin. While the plastic is still hot, smooth it over the pin. ^[5]

   • Never put plastic eyeglass frames directly over a flame.

Advertisement

1. 1

   Use an eyeglass repair kit. Eyeglass repair kits are readily available at drugstores and comprise everything you need to brand a repair--screws, a tiny screwdriver and sometimes a magnifying glass. A newer version of the kit contains longer screws meant to be easier to handle. You insert the screws into the hinges, screw them in and then "snap off" the bottom of the spiral to fit the size of the hinge.

   • If you're finding it difficult to line upwardly the hinges on your temple piece and front piece, it could because a hinge mechanism inside the temple piece hinge is property it back. To correct this, use the hook terminate of a paper clip, insert it through the temple hinge hole and gently pull it out. To go on the hinge hole in place, insert a second paperclip upright and into the "gap" created when y'all pulled out the hinge hole. Line up the front slice and temple slice holes and insert and tighten the screw. When y'all're finished, remove the paperclip from the gap and the hinge hole volition slide dorsum into identify creating a house fit for your glasses. ^{[half dozen]}

2. 2

   Attempt a toothpick. When a spiral falls out of the hinge that holds the front and temple pieces of your glasses together, use a toothpick to temporarily have the place of the screw. Line upwardly the temple swivel holes with the forepart holes and push a wooden toothpick through them as far as it will go. Break or clip off the excess.^[7]

3. 3

   Substitute with a wire. Strip the paper off of a twist tie (the kind that come on a bag of staff of life). Line up the hinge holes and thread the twist-necktie wire through them. Twist the wire in place until the temple feels secure. Cut off the edges of the wire so you don't get scratched. You can likewise use a small rubber pin (the ones that are sometimes used with wearable toll tags). Insert the pivot through the holes to hold the side in place.

Advertisement

1. 1

   Use blistering soda and water. Start, wipe off both your lenses with a microfiber cloth. Adjacent, mix ane teaspoon (4.9 mL) of water with 1 tablespoon (15 mL) of baking soda until it forms a paste-like consistency. And so, use the paste to your lenses and gently scrub your lenses with the substance. Afterward, rinse your glasses with water to wash off the blistering soda mixture. This will likely be all yous need to remove the scratches!^[8]

2. ii

   Employ a household cleaner. Annoying cleansers can exist used to polish scratched surfaces. Waxy products like Lemon Pledge and Carnauba cleaner wax actually fill light scratches with wax. However, the wax will reduce your visibility and require reapplication every few days. You can likewise try rubbing alcohol or diluted ammonia. After treating your spectacles with i of these products, shine them with a soft cloth, ideally one made peculiarly for cleaning glasses.

3. three

   Foreclose future scratches. Lenses are delicate and should be treated with care to forbid them from getting scratched.

   • Apply an eyeglass case. A sturdy, cushioned case volition protect your eyeglasses; place them in a case rather than in your pocket or throwing them directly into your bag.^[ix]
   • Wash your lenses. Clean your glasses every 24-hour interval with soapy water and dry out them with a clean, soft cloth made for this purpose.
   • Stay away from unfriendly products. Some products tin harm your lenses and should be avoided. Don't utilize facial tissues or paper towels to clean your lenses and stay away from anti-bacterial soaps when you launder them.^[10] Be careful when using hairspray, perfume or nail polish remover--they can remove the coatings on lenses.

Advertizement

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

Video

• In a pinch, the go-to method for fixing a cleaved bridge is only to wrap tape around it to hold the 2 pieces in identify. Cull a color tape that matches the colour of your frames most closely or make a manner argument and wrap them in a piece of decorative duct record.

• Proceed glue abroad from your lenses and your fingers

• If a white residue develops on the frames from contact with acetone, try rubbing them with an oil based balm.

Advertizing

• Go on gum abroad from optics until completely dry

Advertising

About This Commodity

Article Summary 10

If you lose a screw from your spectacles, endeavor purchasing an eyeglass repair kit from a drugstore. These have replacement screws and a tiny screwdriver to make the repair easy. If you can't find a repair kit, push a wooden toothpick through the hinge holes. Yous can also wrap a thin piece of wire through the holes and twist it until the temple of your spectacles feels secure. If your glasses have a broken span, keep reading to learn how to ready it yourself.

Did this summary help you?

Thanks to all authors for creating a page that has been read 771,963 times.

Did this commodity help yous?

Source: https://www.wikihow.com/Repair-Eyeglasses

Share this post